# Right Triangle Math for Electrical Apprentices

Trade math on paper

Short answer: when two measurements meet at a square corner, the straight line between their ends is c = √\(a² \+ b²\)\. Square the two leg lengths, add those squares, then take the square root\. If you already know the long side and need a short side, subtract instead: b = √\(c² − a²\)\. Example: a 6\-inch rise and an 8\-inch side shift give a 10\-inch true offset\. Below are five worked examples with original numbers, a table for when to add and when to subtract, common mistakes, and self\-checks\.

Jump to the worked examples , the free member preview or the paid foundation plan comparison \.

## The picture behind the formula

A right triangle has one 90° corner\. The two sides that form that corner are the legs, usually called a and b\. The side across from the square corner is the hypotenuse, c, and it is always the longest side\. The Pythagorean theorem says a² \+ b² = c²\.

Drawing: legs of 6 and 8 inches meet at the square corner; the side across from it is 10 inches, because 6² \+ 8² = 36 \+ 64 = 100 and √100 = 10\.

The formula only works when the corner really is 90°\. On a plan, check that the two dimensions you are using are drawn at right angles to each other before you combine them\.

## Add or subtract? Decide before you calculate

Which side are you solving for?

You know

You need

Do this

Sanity check

Both legs \(a and b\)

The long side c

c = √\(a² \+ b²\): add the squares

c is longer than either leg

The long side c and one leg

The other leg

b = √\(c² − a²\): subtract the smaller square from the larger

The answer is shorter than c

All three sides

Is the corner square?

Compare a² \+ b² with c²

Equal means 90°; c² too big means the corner is wider than 90°

## Five worked examples

### 1\. Straight\-line distance between two boxes on a ceiling plan

On a plan, box B is 8 ft 6 in along the room and 5 ft 3 in across from box A\. How far apart are they in a straight line?

1. Put both sides in inches: 8 ft 6 in = 102 in; 5 ft 3 in = 63 in\.
2. Square and add: 102² \+ 63² = 10,404 \+ 3,969 = 14,373\.
3. Square root: √14,373 ≈ 119\.887 in\.
4. Back to feet and inches: 119\.887 in = 9 ft 11\.887 in, which is about 9 ft 11 7/8 in to the nearest sixteenth\.

Check in decimal feet: √\(8\.5² \+ 5\.25²\) ≈ 9\.991 ft, which agrees\. This is the shortest possible distance, not a cable length to order: a real run follows framing, supports and the route on the drawings, so it is usually longer\.

### 2\. The 3–4–5 check for a square corner

Because 3² \+ 4² = 5², any triangle with sides in the ratio 3 : 4 : 5 has a square corner\. Scaling all three sides by the same factor preserves the square corner: 6–8–10, 9–12–15 and 12–16–20\.

In a paper sketch, the two sides from a corner are labelled 6 ft and 8 ft\. For a square corner, the diagonal between their ends is 10 ft \(120 in\)\. A diagonal of 10 ft 1/2 in with those same sides would give an angle a little greater than 90° \(about 90\.5° by calculation\)\. A shorter diagonal with the same 6 ft and 8 ft sides would give an angle smaller than 90°\.

### 3\. True offset for a rolling offset

A rolling offset moves the run up and sideways at once\. The rise and the side shift form the legs, and the true offset is the hypotenuse\.

1. Rise 6 in, side shift 8 in: √\(36 \+ 64\) = √100 = 10 in true offset\.
2. Rise 5 in, side shift 7 in: √\(25 \+ 49\) = √74 ≈ 8\.602 in, about 8 5/8 in\.

In the ideal diagram, the separate bend\-spacing step would use a supplied angle: at 30°, 10 ÷ sin 30° = 20 in\. This is a triangle calculation\. The [conduit bending guide for offsets, saddles and the multiplier](https://www.tsaielectro.com/conduit-bending-offsets-saddles/) covers that separate step\.

### 4\. Finding a missing short side

A plan shows a diagonal of 25 ft between two points, and one side of the square corner is 7 ft\. What is the other side?

1. Subtract the squares: 25² − 7² = 625 − 49 = 576\.
2. Square root: √576 = 24 ft\.

Sanity check: 24 ft is shorter than the 25 ft long side, as it must be\.

### 5\. The same triangle in AC theory: impedance and power

For this classroom example, assume an ideal linear series R–L circuit in sinusoidal steady state, using RMS voltage and current\. Let R = 8 Ω and inductive reactance X\_L = 6 Ω at the stated frequency, with no other reactance\. Resistance and reactance form the perpendicular components of the impedance triangle, so the impedance magnitude is \|Z\| = √\(8² \+ 6²\) = 10 Ω\. At 120 V RMS, the current is 120 ÷ 10 = 12 A RMS\.

The power triangle follows: real power P = 12² × 8 = 1,152 W, reactive power Q = 12² × 6 = 864 var, and apparent power S = 120 × 12 = 1,440 VA\. Check: √\(1,152² \+ 864²\) = 1,440\. The power factor is 8 ÷ 10 = 1,152 ÷ 1,440 = 0\.8, lagging for this ideal R–L model\. For more on that ratio, see [what power factor means](https://www.tsaielectro.com/what-is-power-factor/) and [single\-phase AC basics](https://www.tsaielectro.com/ac-single-phase-basics-apprentice/) \.

## Common mistakes

- Mixing units\. 2\.5 ft and 40 in cannot be squared together\. Convert both to inches \(30 in and 40 in\) or both to feet first\.
- Forgetting the square root\. 6² \+ 8² = 100 is c², not c\. The side is 10\.
- Adding when you should subtract\. If the long side is known, the missing leg comes from c² − a², and it must come out shorter than c\.
- Rounding too early\. Keep the decimals until the last step, then round to the fraction your tape shows\. Practice reading those fractions with the [tape measure practice guide](https://www.tsaielectro.com/apprentice-tape-measure-inch-fractions/) \.
- Reading a plan at the wrong scale\. Convert drawing measurements with the sheet’s scale before using the formula; the [plan reading guide](https://www.tsaielectro.com/electrical-blueprint-symbols-plan-reading/) covers scales\.

## Check yourself

1\. Legs of 9 ft and 12 ft\. How long is the side across from the square corner?

√\(81 \+ 144\) = √225 = 15 ft\. It is the 3–4–5 shape multiplied by 3\.

2\. The long side is 17 in and one leg is 8 in\. What is the other leg?

√\(289 − 64\) = √225 = 15 in\.

3\. One leg is 2\.5 ft and the other is 40 in\. What is the third side?

Convert first: 2\.5 ft = 30 in\. √\(900 \+ 1,600\) = √2,500 = 50 in, which is 4 ft 2 in\.

## Where this fits and sources

Right\-triangle work shows up in trade\-math and AC\-theory material for electricians\. For a fuller free textbook treatment, see Chad Flinn’s open textbook chapter [Trigonometry, in Trigonometry and Single Phase AC Generation for Electricians](https://workforce.libretexts.org/Bookshelves/Electronics_Technology/Trigonometry_and_Single_Phase_AC_Generation_for_Electricians_%28Flinn%29/01:_Trigonometry) on LibreTexts \(CC BY 4\.0\), and the BCcampus chapter [The Basics of Triangles in Math for Trades, volume 3](https://opentextbc.ca/mathfortrades3/chapter/the-basics-of-triangles/) \. Your program’s own math materials and instructors decide what you are tested on\.

All numbers on this page are original examples, recalculated with a separate script\. This page teaches paper math only; it is not installation instructions\.

## Free preview before you choose a plan

The public membership page includes a free sample on circuits, Ohm’s law and power, with paper calculations\. It is not about triangles; use it to check the explanations before comparing paid topics\.

[See the free preview](https://www.tsaielectro.com/membership/#etp-benefit-preview)

## Paid ET Member plan

This triangle guide is free and complete\. If you also want a broader foundation for the Texas electrician route, compare the topics and terms of the paid ET Member plan with what you need to study\. It is a separate foundation option, not a triangle course\.

[Compare the paid plan topics](https://www.tsaielectro.com/membership/?et_src=article-en-right-triangle-member&et_cta=compare-paid-plans#etp-tier1-h)
